SPERANZA II
Yacht for Sale

Length: 94' 11" / 28.93m | Builder: Sanlorenzo | Year: 2021
Speranza II Yacht for Sale

Speranza II Yacht for Sale - 94'Sanlorenzo

Type: Motorboat
Category: Motor Yacht
Builder: Sanlorenzo
Model: SD 96
Condition: Used
Length: 94' 11" (28.93m)
Beam: 25' (7.6m)
Engines: 2x Inboard, 1,380hp
Speed (Cruising): 14 Knots/16 MPH
Speed (Max): 18.3 Knots/21.06 MPH
Model Year: 2021
Build Year: 2021
Flag: Malta
Staterooms: 5
Sleeps: 11
Features:
Price: €10,900,000 EUR

Contact Us For More Information

    Preferred method of contact:

    Detailed Information



    Builder Sanlorenzo
    Name M/Y Speranza
    Model SD 96
    Year build 2021
    Length overall 28.93 m
    Beam 7.60 m
    Range @ Economical speed ( 10 - 11 Knots) 1756 nm
    Accommodation 11 Guests / 5 Crew
    Current Location Limassol Marina
    Flag Maltese
    Hull material GRP
    Engines 2 x MTU 10V2000M86
    Engines power: 2 x 1380 HP
    Generators: 2 x Kohler 45KW each
    Engines hours 730 hrs
    Generators hours 1676 Prt & 1684 Stb
    Fuel tank capacity 15700 L ( 11860 Main - 3640 Day )
    Fresh water tank capacity 2500 L
    Black & Grey tank capacity 1000 L

    A/C Total Power


    216.000 BTU/h
    Category A




    Engine room equipment
    Sewage treatment system Hammann HL CONT Compact 0125
    Alfa laval (fuel cleaning system) - MIB 303 Separator
    Tender fuel filling system with manual pump
    Automatic Watermaker MC5 Duplex 500lt
    Ozone treatment for air conditioning system
    "puRO GRANDE" Reverse Osmosis Fresh water system 540 l/h
    Stabilizers and Thrusters
    CMC Electric Stabilizers - under way and zero speed
    Side Power - Hydraulic Stern and Bow thrusters
    Satellite and communication systems (TV Sat)
    Empty radome KVH TV8 (2 in total)
    Predisposition for Sat Tv antenna KVH TV8 (cables only)
    Satellite and communication systems (Com)
    Predisposition for KVH Track phone V7-HTS
    Meridian 5G System ( 100Km Offshore Coverage)
    PABX (telephone switchboard) with phone in bridge area

    Cordless phones in master cabin, UD salon, MD salon, crew area (4 in total)

    Alarms and controls
    Lights for anchors
    Open portholes alarm system
    CCTV IP Panasonic (with DVR): 2 fixed in cockpit +2 fixed in lateral passageways, 1 pan & tilt + 2 fixed in engine room
    Color monitor 17'' for CCTV in crew area
    Additional touch screen monitor 12" (ship monitoring system)
    Electronics
    Portable control station MTU (no.1 connection point) – starboard cockpit
    Additional connection point for portable control station MTU - upper deck aft port
    Extra wind control station – upper starboard side
    Electrical Equipment
    Cablemaster - Glendinning CM8 for shore socket 63A (instead of 100/125A as per Schedule 5)
    Inverter Mastervolt 24V 5000W - for sockets 220V
    Additional IP65 waterproof socket 220V in the Garage - in Engine room - in UD External Bar - in Bosom's Locker - in Chain Locker
    Additional IP65 waterproof sockets for exterior areas on aft cockpit sofa - on Custom Pool port
    Additional Shuko sockets 220V - in each Guest Cabins- in the Salon - in the Pantry - in the Master Cabin - in the Galley in the Sky lounge, in the Wheelhouse)
    Additional USB sockets in each Guest Cabins - in the Salon - in the Master Cabin - the Sky lounge - in the Wheelhouse)
    Tender

    Williams Diesel Jet D445

    Audio and video equipment
    TV in upper deck salon 75"
    TV in master cabin 55" & Mirror that hides TV
    TV in salon 55”
    Audio Video Silver Package with the following Upgrades:
    - UD External Aft: 4 Speakers - 1 additional Amplifier Hypex
    - UD Skylounge: 4 Speakers - 1 additional Soundbar & Subwoofer
    - UD Sun Bathing Area and Bow Area: 4 additional Speakers (2 in Sunbathing & 2 in Bow Area) - additional SONOS Amp - additional Hypex
    - MD Salon 5 Speaker B&W CCM362, & 1 Subwoofer)
    - MD Cockpit: 4 Speakers & GRP works for 2 additional Speakers & additional Amplifier Hypex
    Additional Cable CAT6 from A/V Rack to the Hard Top
    Wheelhouse Car Stereo with Bluetooth
    4 Apple TVs in the Lower Deck Guest Cabins
    Additional TV LED Samsung 32" for 5th Guest Cabin
    Internet Wi-Fi System 5G with harbor hot spot antenna

    Additional Wi-Fi Access Point in Engine Room and in Crew Mess

    Household Appliances
    2 Wine coolers 34 bottleseach in salon & galley
    Ice maker (manual refill) in UD bar unit
    Teppan yaki on upper deck

    Additional lower fridge with drawers in the galley

    Cooking top in ceramic glass Miele
    Oven 90 cm Miele

    Professional extraction hood

    Complements for the exterior
    External inox shower column on upper deck
    Sun awning for the stern area of the Upper Deck
    Teak floor for upper deck including full beam area & bow area including the stairs step
    Skylounge side doors in lieu of standard fixed side glass
    Full beam canvas for sunbed (Portuguese deck)
    Boffi Bar unit model K4 with sliding top
    Dimmer package for exteriors
    Exterior bar with sliding top mod. K4 by Boffi, on the flybridge
    Mosquito net for all Lower Deck Openable Portholes
    Disappearing Stern Shower
    Stainless steel bar for exercises on the flybridge
    Sun awning for bow area
    12 Underwater lights led RGBW 4 aft & 4 on each side
    Additional chain length of 27,5m
    Electric Sliding Door in main deck salon


    General

    Composite materials (GRP) will be used for the construction of the hull, decks and superstructure.

    The vessel will be built with vinyl-ester resin (for the first three layers of the hull lamination) and polyester isophthalic resin for hull plating, structures and GRP accessories. The Gel coat is of Neopentilic type; reinforcement fibres are, depending on their use, mat, roving’s, multi-axial and unidirectional glass as indicated in the structural drawings approved by Classification Society.

    The PVC of the sandwiched core will be of closed cell type, density between 50 and 90 Kg/m3.

    The structure shape and the scantling will follow the most recent knowledge on design and construction for this type of GRP Vessel, in order to ensure maximum structural continuity and lowest possible levels of vibrations and noise. The hull bottom will be built in single skin of different thickness, the sides in sandwich with PVC core, in compliance with the Classification Society regulations, the structure is longitudinal type, with girders and transversal bulkheads as main structural elements. Two watertight bulkheads will divide the vessel into three

    watertight compartments as follow:

    - Engine room.

    - Guest and crew accommodation.

    - Technical locker at bow.

    All openings for pipes and cables going through main bulkheads will be made watertight.

    All bilges will be painted; in the engine room self-extinguishing paint will be used where necessary.

    Exhaust gas pipes and ventilation ducts are GRP moulded and integrated into the structure; flame resistant gel

    and self-extinguishing resins are used wherever necessary.

    Special reinforcements will be placed in way of propulsion and manoeuvring machinery’s foundations,

    generators, shaft line, brackets, rudders, and thrusters’ propellers.

    The hull will be treated with anti-fouling paint. The material will be supplied by a recognized manufacturer.

    Main deck

    The main deck plating is sandwich type, with different thickness as per Classification Society Regulations. The

    structure is longitudinal type, with transversal bulkheads as main structural elements.

    A watertight hatch will be mounted in way of the engine room to allow the mounting and disassembly of the

    Main Engine and other machinery.

    Special reinforcements will be placed near all manoeuvring devices such as windlasses, capstans, hatch hinges,

    cranes and gangway.

    All openings for pipes and cables going through the Main Deck will be made watertight.

    Superstructure

    The fly deck plating is sandwich type, with different thickness as per Classification Society Regulations. The

    reinforcement structure is of longitudinal type, with transversal stiffeners and bulkheads as main structures.

    Pillars and longitudinal stiffeners as additional elements.

    A watertight hatch will be mounted in way of the engine room to allow the mounting and disassembly of the main Engine and other machinery. Special reinforcements will be placed in way of the main stressed area like side doors and bases of the Hard Top.

    Structural Bulkheads

    Adequate structural bulkheads are provided in compliance with the General Arrangement Plans, two of these will be also watertight.The bulkheads will generally be made in marine plywood sandwich with polyethylene (“Laricross” or similar) or marine plywood core, with adequate thickness.

    The escape hatches will be located in accordance with the Classification Society Regulations.

    Tanks – Capacity plan

    All the tanks on board are “structural” type, integrated into the hull in such a way to reduce the occupied space and optimize storage room. Tanks are built in GRP, laminated in monolithic and sandwich, laminated on board and then assembled on board. They are designed with enough internal reinforcements to provide the continuity of the hull stiffness.The daily fuel tanks are positioned longitudinally, on port and starboard side respectively, in engine room and

    occupy the space between the bottom, the sides and the deck. On the tank will be installed an adequate flange for “gas free” treatment and for washing.

    The main fuel, fresh, grey and black water collection tanks are laminated on the keel after having completed the hull bottom lamination.

    For fresh water tanks will be foreseen a layer of non-toxic gelcoat.

    Tanks are installed with an adequate distance from the bottom to prevent any damage and fluid leakage in case of tolerable collision of the hull. The tanks will be fitted with the necessary vents and fittings and they will be pressure tested as required by the Classification Society Regulations.

    Insulation

    The insulation is provided to guarantee maximum comfort and safety onboard the vessel in all circumstances.

    The engine room noise and thermal insulation from the other vessel areas is as follows:

    - Ceiling, walls and bulkhead insulation between the engine room and the accommodation areas inside the

    engine room, will be realized with thermal insulation sandwich fixed by needles and finished with steel

    plate fixed onto aluminium grid supports.

    - Engine room/ accommodation area, accommodation side realized with thermal insulation sandwich fixed

    with needles, integrated onto floating bulkhead on viscous-elastic elements.

    - Insulation of extraction and ventilation trunks realized with insulation sandwich fixed with needles on

    Engine room side.

    - Insulation of gas exhaust piping realized with thermal insulation sandwich guaranteeing optimal thermal

    insulation, flame resistant and self-extinguishing.

    - Thermal/acoustic insulation on main deck floor, in correspondence of the engine room compartment,

    realized with insulation material fixed by needles onto floating floor on viscous-elastic elements.

    Accommodation areas insulation is realized as follows:

    - Acoustic insulation of each cabin realized with insulation sandwich inserted into the bulkheads and the

    flooring.

    - Thermal/Acoustic insulation between the crew quarters and guest cabins realized with thermal insulation

    sandwich fixed with needles, integrated onto floating bulkhead on viscous-elastic elements.

    - Thermal/Acoustic insulation of the walls and exposed surfaces realized with thermal insulation sandwich

    fixed with needles.

    Teak deck

    The main deck will be covered in high quality teak with planks 12mm thick glued directly onto the deck. Teak will cover also the steps leading to swimming platform.

    Weathertight Doors, portholes and hatches

    Weathertight side doors will be built in aluminium and GRP, with hand wheel closing systems, fitted with

    stainless steel hinges and locks.

    The weathertight deck hatches will be made of aluminium/reinforced polymer covered in teak or steel and

    tempered glass with manual closing system and block system on opening position.

    The watertight portholes will be in stainless steel AISI 316 and tempered glass.

    Windows

    Windows of main deck will have crystal panels with black border edges, designed with the width and

    characteristics as required by the CE Rules.

    The wheelhouse windows will be stratified and fitted with windscreen wipers.

    All fixed windows of the hull and superstructures will be flush mounted glued directly to the GRP.


    Main engines

    2 x MTU 10V2000M86

    Gearboxes

    2 X ZF 2000 V, R = 2.92:1

    Propellers

    In Class “S” NiBrAl Alloy, designed to optimize comfort and performance.

    Shafts

    Made of Aquamet 17 or equivalent, diam. 90 mm (tolerance ± 1mm); supported on bronze brackets and

    stern tube. Mechanical seals on tube’s ends.

    Rudders

    In AISI 316 stainless steel, surface and stock to ensure excellent manoeuvring performance. Rudder holes

    with steel tube and bronze flanges, stocks in AQ 17 or equivalent.

    Steering System

    Steer by wire system with signal sends by CANbus and 400/24V linear actuators.

    Bow Thruster

    Hydraulic 560Kgf thrust bow thruster in a 400mm GRP tunnel integrated into the hull, with remote control

    lever in the wheelhouse and on wings station.

    Intruder

    A fixed intruder, made in stainless steel (AISI 316), will be installed on the transom. The intruder will be

    painted with antifouling.

    Anchor Windlasses & Capstans

    N. 2 electric anchor windlasses 4000 W, 400V, reversible, will be installed.

    Remotely and locally operated.

    N. 2 electrical stern capstans 2200W, 400V will be installed.

    Stabilizers

    A couple of electrical fins stabilizers will be installed on the hull with dedicated touch screen control panel

    placed in wheelhouse.

    The system can work at the following conditions:

    - zero Speed with the boat at anchor;

    - under Way with the boat sailing.

    and will have the following characteristics:

    - digital Stabilizer;

    - digital touch screen control panel in wheelhouse;

    - actuators 400VAC/3ph/50Hz with a power of approx. 5 kW;

    - fins in GRP material with a surface of approx. 1,4m2 each;

    The hull structure where fins will be installed will be reinforced in accordance to the Class Rules.

    The stabilizer fins will be painted with antifouling.


    General

    All piping will be identified with labels indicating the type of plant as well as the flow direction. Colour

    coding will be in accordance with the regulations in place.

    All the sea cocks, valves, levers and pumps will be marked with identification labels in English.

    Bilge System

    Sistema c Centralized system with suction in each watertight compartment realized with IP 68 solenoid

    valves remotely and locally operated. A portable suction device located in the engine room is linked to the

    main manifold.

    E/pump 400V, maximum capacity 200 l/min, with control stand at pump (reversible also for fire fighting

    system).

    24Vdc automatic bilge E/pumps, in each watertight compartment.

    Emergency suction device located in the engine room linked to the main engines cooling system.

    High level water sensors in each watertight compartment with relevant alarm in the wheelhouse.

    Pipe material: CuNi/ approved fire-resistant flexible pipe.

    Safety & Fire Fighting System

    The onboard fire fighting systems is made up of the following components:

    - Centralized Fire FightingFM200 for the engine room. The activation of this system is positioned on the

    main deck aft cockpit.

    - Saltwater Fire Fighting System consisting of one E/pump 400V (interchangeable with the bilge pump)

    with maximum capacity 200 l/min, located in the engine room and connected to two fire hydrant on

    main deck. The pump control command is on the wheelhouse touch screen, on engine room main

    switch panel, and also next to the anchor windlasses. The pump can also be utilized for anchor chain

    washing.

    - Portable powder and CO2 fire extinguishers will be positioned as per CE Rule.

    Pipe material: CuNi/Galvanized steel.

    Fuel system

    The Yacht fuel system total capacity is approx. 15.700 l, distributed between daily fuel tanks (circa 1.800

    l/cad) and main storage tanks (aprox 7.500 l and 4.600 l respectively). Each tank will be fitted with vent

    pipes.

    Two electrical gauges will be installed: one for the main tanks and one for the daily fuel tanks.

    Tank levels and relevant alarms are monitored on the wheelhouse touch screen and on the main engine

    room switch board panel.

    Fuel filling will be made by gravity through a dedicated filling locker located on each side of the vessel.

    The fuel transfer is made by a 380V main pump, controlled by the main switch board panel and by the

    wheelhouse touch screen monitor from which it would be possible to set the automatic transfer. In case of

    damage, one 24V emergency electric pump and one emergency manual pump are installed.

    The fuel supply (with fuel filters) to main engines and generators will be done by gravity from the daily fuel

    tanks.

    Pipe material: Stainless steel AISI 316/copper/approved fire-resistant flexible pipe.

    Fresh Water System

    The fresh water is supplied from a structural tank located in the aft engine room area, with a capacity of

    approx. 2.500 l, or through a dock connection located inside the transom side hatch, provided with

    pressure reduction valves. Fresh water tank levels are indicated on the wheelhouse touch screen monitor

    and on the main electrical panel.

    Fresh water system main components are:

    - Fresh water pressure system group made up of two E/pumps: one 400V tri phase and one 24V

    maximum capacity 80 l/min, positioned in the engine room, supplying water to the several boat users

    such as sinks, showers, toilets, bidet, domestic appliances.

    - N. 2 stainless steel 100 l boilers

    Pipe material: Multilayer material.

    The piping for hot water will be appropriately insulated.

    Grey & Black Water Systems

    Grey water system is made of a tank located in the engine room bilge with a capacity of approx. 1.000 l, for

    run-off water collection from showers, sinks, bidets, dishwasher, washing machine and WC. Tank level is

    displayed in the wheelhouse touch screen monitor and on the main electrical switchboard.

    One 380 V tri phase E/pump, with maximum capacity of 50 l/min, is installed in the engine room for the

    grey water tank discharge. It may be controlled manually from the wheelhouse touch screen monitor or

    main electrical panel. In case of failure it will be possible to discharge directly overboard the run-off water

    discharge from galley, washing machine and dishwasher.

    For tank discharge by shore dock while moored, an international socket will be provided.

    An emergency E/pump 380 V tri phase with a maximum capacity of 50 l/min is installed in by-pass.

    Pipe material: Stainless steel AISI 316/PVC.

    Sea Water System

    Sea water system is made of following;

    - N. 2 sea water intakes for: main engines, gearboxes, gas exhaust raiser, shaft seals, side exhaust

    housing moulding cooling

    - N. 2 sea water intake for each gen set cooling

    - N. 1 sea water intake for fire fighting system

    - N. 1 sea water intake for air conditioning pump system

    If requested, connection to the sea water intakes will be also provided for: water-maker system and black

    water treatment system.

    All sea water intakes are fitted with filters and valves.

    Pipe material: CuNi/Stainless steel AISI 316/Bronze.

    Hydraulic System

    An independent E/hydraulic unit for gangway, garage hatch and tender hauling/launching system with an

    emergency hand pump.

    Each hydraulic unit will be fitted with a dedicated oil collecting tank and with a separate circuit.

    Main Engines & Main Generators Exhaust

    - Discharge pipes AISI 316 and 304 covered with appropriate insulation, of adequate dimensions as

    recommend by the main engine’s manufacturers.

    - AISI 304 will be used for raiser piping “dry” areas, and AISI 316 will be used for the raiser piping “wet”areas cooled by sea water.

    - AISI 316 will be used also for the low rpm by-pass exhaust pipes.

    - Underwater discharge structural pipes in GRP, fairing sections to facilitate the gas release.

    - GRP side exhaust housing moulding along the hull with stainless steel grids for the low rpm by-pass.

    - Gen sets gas exhaust pipe system made in approved rubber housing, muffler and water/smoke

    separator in GRP for noise reduction. The exhaust gas discharge will be realized by GRP carters on

    both port and stbd side of the vessel.

    Scuppers

    Scuppers for rain and fresh water located on the main deck and on the flybridge will discharge directly

    overboard.

    Pipe material: Stainless steel AISI 316/CuNi/PVC.


    Engine Room Ventilation

    - N. 2 reversible E/ventilators 400V tri phase with a total capacity of 15.000 m³/h installed for engine room

    ventilation

    - N. 1 E/circulator 400V tri phase installed for air circulation under the garage box.

    Extraction System for accommodations

    In the accommodation areas a forced 230V/380V E/Air extractor will be fitted.

    Air extractor system works together to air treatment.

    The air treatment will be fitted in the following areas: owner’s cabin in the main deck and Guest/Vip’s

    cabins for lower deck.

    AIR CONDITIONING

    Conditioning & Heating

    An air conditioning system will be installed, with a total capacity of approx. 180.000 BTU/h. The cooling

    unit, sea water and circulation pumps will be in the aft engine room area.

    Fan coils will be installed in each area in suitable numbers depending on the layout and system dimensions.

    All fan coils will be installed with suitable drip trays that will discharge condensation water directly

    overboard (by gravity or by dedicated electric pumps).

    All ail be provided with insulated plastic houses with joints in press-fitting.



    Main Characteristics

    The onboard main voltages will be the following:

    - 400 V tri phase, 50 Hz for main power circuits.

    - 230 V mono phase, 50Hz, for lighting systems, domestic appliances and other users not feed by 400V

    system.

    - 24 V DC with negative to earth for small power circuits, visual signals, emergency lighting, electronics,

    communication systems, propulsion system and main engine start up.

    - 12 V DC for main gen set starting and VHF.

    Electric cable dimensions are properly sized related to the maximum amperage involved and made from

    certified material that avoid flame propagation; they are housed in metal trays or self-extinguishing PVC

    closed type raceways.

    The main switchboards are in:

    - Engine room.

    Distribution switchboards will be also located in strategic area so that they can be easily recognized,

    reached and operated.

    All on board equipment will be earthed through copper stripes earth bands of suitable dimensions.

    The grounding system will be the following:

    - metallic components, sea water intakes, sea cocks, etc. This system will consist of two copper stripes

    laid throughout the yacht and connected to the aft zinc anodes;

    - grounding system for electrical components. It will link all control panel grounds and electrical

    equipment grounds; it will be connected to dedicated porous plate;

    - grounding system for the navigation electronic equipments. It will be connected to dedicated porous

    plate.

    Power Sources

    Gen sets

    Two (2) gen sets one 45 kW each, 400 V tri phase, 50 Hz, located in the engine room and mounted on silent blocks. The gen sets will be fitted with sound proof encasing, hour counter, switchboard

    for start/stop and control. Gen sets starting control will also be located on the wheelhouse touch screen monitor

    Shore Connections

    One 400 V tri phase, 63A, 4 poles shore power connection located on the stern and connected with an

    insulated transformer 400V/400V tri phase, 45kVA: connection is star point to provide 230 V.

    Alternating current energy sources will be controlled by the main switchboard panel. On the switchboard

    front door a voltmeter and a 400V frequency meter are installed. Power sources will be protected by

    adequate power fuses or switch breakers and remote control switches are provided to managing them on

    the yacht electric supply. Shore power system will be connected to a bar, protected by a thermo magnetic

    switch, from which the power will be distributed to all yacht devices.

    Batteries

    Service Batteries: a 600Ah/24V gel accumulator battery bank will be fitted in the engine room, to supply

    the following services:

    - signalling;

    - small power circuits;

    - navigation lights and relevant switchboard;

    - navigation electronics;

    - monitoring.

    MTU Elecronics Batteries: a 200 Ah/24V gel/AGM battery bank will be fitted in the engine room, to

    supply the Main engines electronic equipment.

    Main Engine Starting Batteries: 2 sets of gel/AGM batteries with a capacity of 240Ah @24 Vdc will be fitted

    for the main engines starting, located in engine room. These batteries will be high capacity instant

    discharging 1200A type.

    Generator Starting Batteries: 2 sets of gel/AGM batteries, starting type, [email protected] 12V for each group for

    gen set starting. These batteries will be high capacity instant discharge 800A type. Each battery will be

    located in a dedicated space near the gen sets.

    Battery charging system

    Battery chargers are provided to recharge service batteries, VHF, emergency, Main engines starting and

    electronics and gen sets starting battery banks:

    - N. 2 automatic battery chargers 75A/24Vdc to recharge service batteries, located in the ER.

    - N. 1 automatic battery charger 25A/24Vdc with switchboard to recharge main engine starting

    batteries, and electronic batteries, located in the engine room.

    - N. 1 automatic battery charger 25A/12Vdc, to recharge gen sets starting batteries, located in

    the engine room.

    - N. 1 automatic battery charger 10A/12Vdc, to recharge VHF batteries, located in the technical

    space under the wheelhouse.

    The battery chargers listed above will function automatically, with no-manual operation availability.

    Battery charging system by alternator

    Main engine starting batteries and service batteries will be also charged by main engines alternators, and

    their charge is managed by a load charging dispatcher. Gen set alternators will charge their own stating

    batteries. A thermo magnetic switch or fuse to protect 24V dc users lines connected to the main

    switchboard is provided.

    Lights & Sockets

    Lighting of the engine room: 230/24V by means of ceiling led bars.

    Lighting in the accommodation areas is generally by means of led spotlights.

    Each cabin will be provided with the following devices:

    - ceiling lights with controls close to entrance door and nightstand;

    - reading light on behead with control close by;

    - lights on bathroom ceiling with controls close to bathroom door;

    - lights on bathroom mirror with controls close by;

    - cabin sockets: 230V;

    - bathroom sockets: 230V.

    Lighting of the living areas, stairways and exits are made up of the following components:

    - ceiling lights in the dining room and saloon with controls located in various places;

    - ceiling lights with controls near to the exits;

    - courtesy lights on stairs;

    - 230 V sockets.

    One dimmer circuits will be provided in the cockpit, saloon, dining room, Owner’s Cabin.

    The exterior lighting will be by watertight led spotlights.

    Alarms and Main Systems Controls

    The following electrical control appliances will be installed:

    - Voltmeter and ammeter to control 400V system, visible on both the wheelhouse touch screen monitor

    and the main switch board.

    - Illuminated push buttons for shore line power connection/disconnection on both wheelhouse touch

    screen monitor and main electrical switch board.

    - Gen set overload warning lights on wheelhouse touch screen control panel.

    - Controls for generator start up and connection/disconnection on both the wheelhouse touch screen

    monitor and the main switch board.

    - Control for closing/opening of electrical systems sections on the main switchboard and on wheelhouse

    touch screen monitor.

    - Absorption Ammeter on wheelhouse touch screen monitor and main switchboard for battery charge.

    - Ammeter on wheelhouse touch screen monitor and main switchboard for battery discharge.

    The following alarms will be installed:

    - Engine and gearbox alarm repeaters in the wheelhouse.

    - Fuel high/low level alarm on wheelhouse touch screen monitor.

    - Fresh water high/low level alarm on wheelhouse touch screen monitor.

    - Grey and Black water high level alarm on wheelhouse touch screen monitor.

    - Bilge water high level alarm on wheelhouse touch screen monitor and main switchboard.

    - Smoke detection alarm for all inside areas of the vessel on wheelhouse touch screen monitor.

    - Alarm for the opening of the garage hatch.


    Wheelhouse Control Station

    - N. 3 x 16” multi-function colour display.

    - N. 1 speed, depth, wind and temperature indicator.

    - N. 1 rudder angle indicator.

    - N. 1 autopilot.

    - N. 1 VHF.

    Hard Top

    - N. 1 GPS antenna.

    - N. 1 radar open array antenna 4”.

    - N. 1 VHF antenna.

    - N. 1 Air signalling horns.

    - N. 1 search light with controls located in wheelhouse and cockpit helm station.

    - N. 1 Wind transducer.

    Audio/Video System

    The following equipment will be installed on board:

    Salon

    - N. 1 “smart TV” LED 50”.

    - N. 1 Multi area amplifier with AIR play, kit home theatre with subwoofer connected to the aft cockpit

    and fly deck with 5 speakers.

    - N. 1 IPAD Mini for centralized control with Docking station

    Owner’s cabin

    - N. 1 “smart TV” LED 43’’.

    - N. 1 Amplifier with AIR play, kit home theatre with subwoofer and 2 speakers.

    - N. 1 IPAD Mini for centralized control with Docking station

    Vip cabin

    - N. 1 “smart TV” LED 32’’.

    - N. 1 amplifier with 2 speakers.

    - N. 1 infrared repeater

    Guest’s Cabins, port and stbd

    - N. 1 “smart TV” LED 32’’.

    - N. 1 amplifier with 2 speakers.

    - N. 1 infrared repeater.

    Crew mess

    - N. 1 TV LED 24”.

    - N. 1 wireless hifi amplifier with 2 speakers.

    - N. 1 infrared repeater.

    Captain cabin

    - N. 1 Jbl Bluetooth portable speaker

    Cockpit, main deck

    - N. 2 couples of speakers in the ceiling with connection from Salon

    - Mini IPAD control of Salon

    Upper deck, aft area

    - Speakers predisposition.

    Sky lounge

    - TV Prearrangement.

    - N. 1 Amplifier with AIR play with 2 speakers.

    Timoneria

    - N. 1 Sonos amplifier with two (2) speakers


    Hull

    - Porthole in stainless steel AISI 316 with tempered glass and frame in stainless steel

    - Fender bar in stainless steel and rubber on each side of the vessel

    - Anchor pocket in stainless steel recessed into the hull

    Main deck

    - Teak decking on main deck with 12mm thickness planks, in cockpit and sideways

    - Teak on stair leading up to the fly-bridge from the cockpit.

    - Teak decking on stairs leading down to the lift swimming platform.

    - Teak grating 20mm thickness on the lift swimming platform from the cockpit.

    - Handrail in stainless steel on stairway leading down to the lift swimming platform.

    - Handrail in stainless steel on stairway leading up to fly-bridge.

    - Tempered glass windows of approved thickness.

    - Lift swimming platform with electro-hydraulic power system.

    - Electro hydraulic gangway with teak grating and frame in stainless steel, retractable inside the upper

    step of the port stair case.

    - Manual Swimming ladder.

    - Control panel for gangway and garage hatch manoeuvring.

    - Electrical sockets for shore line in a dedicated stern hatch.

    - Shore fresh water filling station, shore water connection and hot/cold mixer for shower located inside a

    dedicated stern hatch.

    - External deck lighting by watertight led lights.

    - Shore connection for black water discharge in a dedicated stern hatch.

    - Fresh water filling station.

    Fairleads and Bollards:

    - N. 4 fairleads in stainless steel at bow, two for each side;

    - N. 3 bollards in stainless steel for each side (one astern, one at bow and last one at midship);

    - N. 2 up and down bollards situated on the bathing platform;

    - N. 2 foldable sunpad on each side.

    10.2.1 External passageways and aft cockpit

    - Gates in stainless steel to access the lift swimming platform.

    - Saloon sliding door in tempered glass

    - N. 2 side doors in GRP, one on each side, for side mooring boarding.

    - Glass door for flybridge access from the cockpit on stbd side.

    - Structural stairs to access the fly-bridge from the aft cockpit, stbd side.

    - Structural stairs to access the fly-bridge from port sidewalk.

    - GRP integrated sofa.

    - N. 1 coffee table.

    - N. 2 armchairs.

    - N. 2 electric windlasses with integrated capstan 400V, 2200W tri phase.

    - Fire fighting hose with shore.

    - Brackets for boat hooks recessed inside a dedicated space on the internal bulwark.

    - Fuel filling station on starboard side.

    - N. 2 doors on starboard side to access the side passageways of the main deck.

    - External cushions (See Materials and Furnishings).

    - Protection covers for all exterior furniture.

    - GRP door to access the engine room from the port side.

    - Engine room emergency hatch in aluminum covered with teak.

    - Audio/Video system as indicated previously in Par.9.3.

    Bow area

    - Antiskid deck finishing.

    - N. 2 GRP side sofas.

    - N. 1 technical storage, with an access from dedicated hatch on the deck, for store deck equipment and

    windlass electrical panel.

    - Stainless steel handrail.

    - Chain locker provided with suitable drainage system.

    - N. 2 anchor windlasses with integrated capstan, reversible, 400V 4000W.

    - N. 4 drainage scuppers.

    - Local control of windlass by means of portable device.

    - N. 2 high-holding power galvanized steel anchor, 136Kg each.

    - N. 2 Chains 14mm, length 110m each (2 x 4 lengths).

    - Chain locker provided with suitable drainage system.

    - Chain locker provided with suitable drainage system.

    - Fire fighting hose with shore.

    - Fresh water for deck washing.

    - External cushions (See Materials and Furnishings).

    - Protection covers for all outdoor furniture.

    - N. 2 drainage scuppers.

    10.3 Fly Bridge

    The fly bridge may be reached through an external staircase coming up from the cockpit, from the

    wheelhouse/Sky lounge or through an external central stairway to the bow area.

    The main areas of the fly bridge will be equipped as follows:

    Aft sun pad area

    - Antiskid deck finishing.

    - N. 4 chaise longues.

    - N. 1 sofas.

    - N. 1 coffee table.

    - Bar area with fridge and sink.

    - N. 4 drainage scuppers.

    - N. 2 self-inflatable life-rafts for 8 people each laid in dedicated superstructure flash room provided with hydrostatic launching system.

    - Handrail in stainless steel on the stairs leading down to the cockpit.

    - Handrail in stainless steel-teak-tempered glass on the aft pulpit.

    - External cushions (See Materials and Furnishings).

    - Covers for all outdoor furniture.

    - Fresh water for deck washing.

    - Audio/Video set-up as indicated in Par.9.3.

    Hard Top area/ Sky Lounge

    - GRP hard top with navigation lights, antennas, acoustic alarm, search light and fly bridge lighting.

    - Parquet floor.

    - Table for 8/10 people and chairs.

    - Cabinets to hold plates, glasses, and crockery on each side.

    - Accessory for crockery inside cabinets.

    - Door with folding elements in tempered glass.

    - Door to wheelhouse access, on stbd side.

    - Electrical curtain for sky-light

    - Manual curtains.

    - Audio/Video set-up as indicated in Par.9.3.

    Wheelhouse

    - Leather covered dashboard with navigation instruments.

    - Sofa.

    - Nautical chart area.

    - Cabinet.

    - Ceiling covered in wood or leather

    - Parquet floor.

    - Access door on stbd side aft bulkheads, to skylounge.

    - Access GRP/Aluminum door for external passageway to stbd side.

    - Stairs leading down to the starboard foyer covered in carpet or wood with non-slip finish.

    - Helm station supplied with:

    - Main Engine throttles with synchronizer.

    - Main Engines and gearboxes instruments

    - Navigation instruments indicate in Par. 9.1.

    - Bow thruster controls.

    - Electric control panel for repeat alarms and controls already on the touch screen.

    - Touch screen Monitor 12” to control the main onboard systems including: 230V/400V and 24V

    electrical circuits, horn commands, navigation lights, E/pump fuel transfer, anchor windlass, E/fire

    fighting pump, alarm for high level water in bilge and controls for automatic bilge pumps, tank level

    indicators, smoke detector indicators.

    - Sub switchboard 230/400V and 24V.

    - Synoptic navigation lights with manual control.

    - Synoptic alarms and bilge pumps.

    - Manual controls for windscreen wipers, horn, E/pump wheelhouse and autopilot.

    Full Beam Area

    - External passageways, o stbd side, with GRP stair covered with teak.

    - Antiskid deck finishing.

    - 2 Armchairs.

    - N. 1 coffee table.

    - N. 1 storage cabinet.

    - External cushions (See Materials and Furnishings).

    - Protection covers for all outdoor furniture.

    - N. 2 drainage scuppers.


    The Yacht including all onboard machinery and equipment, will be built according to Dir. 2013/53/EU, with
    RINA surveying, in according to the following rules:

    ISO 10087 Craft identification - Coding system
    ISO 14945 Builder’s plate
    ISO 11192 Graphical symbols
    ISO 15085 Man-overboard prevention and recovery
    ISO 11591 Field of vision from hel position
    ISO 10240 Owner’s manual

    RINA Rules Dimension and Construction of Hull

    ISO 9093 – ISO 12216 Openings of hull, decks and superstructure
    ISO 11812 Watertight cockpits and quick-draining cockpits
    ISO 12217 Stability and buoyancy assessment and categorization
    ISO 15083 Bilge-pumping systems
    ISO 14946 Maximum load capacity
    ISO 9094 Fire protection
    ISO 15084 Anchoring, mooring and towing
    ISO 7840 Fire resistant fuel hoses
    ISO 10088 Permanently installed fuel systems
    ISO 10133 Electrical system – Extra low voltage d.c. installations
    ISO 11105 Ventilation of petrol engine and/or petrol tank compartments
    ISO 13297 Electrical system – Alternating current installation
    ISO 10592 Hydraulic steering system
    ISO 8099 Machinery and systems